![]() ![]() Hit enter, and you have a REPL prompt.įor more dfu-util info see. In device manager you can look in ports to see what COM port it gets assigned, then you can connect to it at that COM port at 115200 b/s. You can now plug your MicroUSB cable into the main MicroUSB cable on the board (labeled CN1). It won't hurt anything to leave that breakout board connected as long as there is no MicroUSB cable plugged into it. ![]() You'll also probably want to disconnect all the wires coming from MicroUSB breakout board. Once download is complete, disconnect the USB cable from the MicroUSB breakout board, remove the jumper between 3V3 and GND, and put the JP3 jumper back to U5V from E5V. The command I ran to upload the firmware was.Ĭ:\Users\me\Downloads\dfu-util-0.9-win64>dfu-util -alt 0 -D C:\Users\me\Downloads\NUCLEO_H743ZI-20210202-v1.14.dfu Open a command prompt and navigate to the dfu folder that you downloaded earlier. In device manage under USB devices you should see "DFU in FS mode". Plug in the USB cable from the computer to the MicroUSB breakout board. Resuelve las vulnerabilidades existentes en Windows que podran permitir la elevacin de privilegios si un atacante consiguiera iniciar sesin en el sistema. Connecting 3V3 and BT0 together will cause the board to enter dfu mode when we power it on. BT0 pin is right next to the GND pin we are using. Connect that pin to CN11 BT0 (this is the BOOT0 pin). On top of the board there is a 16 pin black female connector labeled SDMMC. You change this jumper if you want to power the board from 5V from outside the board (not through its normal USB connector)Ĭonnect VBUS from MicroUSB breakout board to E5V on CN11 (pin labels are on bottom of the board) This puts the USB 5V onto the boards 5V.Ĭonnect GND from MicroUSB breakout board to GND pin on CN11 (right below E5V)Ĭonnect D+ from MicroUSB breakout board to PA12 on CN11 (positive data line for USB connection)Ĭonnect D- from MicroUSB breakout board to PA11 on CN11 (negative data line for USB connection) I found this in the Nucleo documentation on STs website. Mine has JP3 on the main board, and not the little board with the ST-Link on the end. I believe there are two versions of the H743 board. Micropython DFU file for the H743 board from here. MicroUSB breakout board (you can get 10 for like 4 bucks on amazon) Just documenting what I did to save the next person some time. It seems, for some, it's not a problem (with many different types of Nucleo boards), for others, it's a repeating trouble with the very same set of boards.This guide should no longer be used. This strange behaviour seems to be very common among developers, meanwhile, very poorly documented. I found TeraTerm stopped working almost from one apload to the next one. No way to upload the software.įurhtermore. Since about 2 hours, every tries ends up in a complete fail. In 9 out of 10 tries are recejted by this error, and only the second attempts seems to be working. The main problem seems to be originated to the 0x800703ee error, when I'm going to upload the. Since about the last 4 hours, the system is down, I can not upload any working code, can't debug, etc. Nucleo under Windows 10Īfter an almos successful day using my new Windows 10 desktop and my good-old Nucleo 401, I have started experiencing some strange behaviour. To start a new conversationĤ years, 4 months ago. Important changes to forums and questionsĪll forums and questions are now archived. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |